1 meets aec-q200 requirements suppression of common mode noise without attenuating the signal magnetically shielded versions for lower rdc and higher current usb 3.0 and other high speed differential signal lines (ieee1394, lvds) pe-1812accxxxsts mechanical schematic usa 858 674 8100 germany 49 7032 7806 0 singapore 65 6287 8998 shanghai 86 21 62787060 china 86 755 33966678 taiwan 886 3 4356768 electrical specifcations @ 25c - operating temperature -40c to +125c part number common mode impedance (10mhz) inductance (uh) standard tolerance rdc ( ? max) idc (a max ) min typ PE-1812ACC110STS 300 600 11 +50/-30% 0.5 0.36 pe-1812acc220sts 600 1200 22 +50/-30% 0.6 0.31 pe-1812acc510sts 1500 3500 51 +50/-30% 1.0 0.23 pe-1812acc101sts 3000 7500 100 +50/-30% 2.0 0.20 all units in mm 14 23 4.50. 2 3.20. 2 3.8 ref 0.65 ref 0.7 re f 3.0 ma x 5. 9 3. 2 3. 4 1. 6 1 2 4 3 weight ......................120 grams/reel tape & reel ..................150/reel w717.b (11/15) pulseelectronics.com automotive chip choke emi suppression for can-bus networks 2-line common mode chokes ?
2 PE-1812ACC110STS impedance vs frequency temp vs dc current 0. 1 1 10 100 1,000 10,000 11 0 100 1,000 fr equency(mhz) impedanc e( ) co mm on mo de di?eren al mo de 0. 0 10.0 20.0 30.0 40.0 50.0 60.0 0. 00 .2 0. 40 .6 0. 81 .0 id c( a) e t( ) et@ 25 0. 1 1. 0 10. 0 100. 0 1,000. 0 10,000. 0 11 0 100 1,000 fr equency(mhz) impedance( ) co mm on mo de di?eren al mo de 0. 0 10.0 20.0 30.0 40.0 50.0 60.0 0. 00 .2 0. 40 .6 0. 8 id c( a) e t( ) et@ 25 pe-1812acc220sts 0. 1 1 10 100 1,000 10,000 11 0 100 1,000 fr equency(mhz) impedanc e( ) co mm on mo de di?eren al mo de 0. 0 10.0 20.0 30.0 40.0 50.0 60.0 0. 00 .2 0. 40 .6 0. 81 .0 id c( a) e t( ) et@ 25 0. 1 1. 0 10. 0 100. 0 1,000. 0 10,000. 0 11 0 100 1,000 fr equency(mhz) impedance( ) co mm on mo de di?eren al mo de 0. 0 10.0 20.0 30.0 40.0 50.0 60.0 0. 00 .2 0. 40 .6 0. 8 id c( a) e t( ) et@ 25 w717.b (11/15) pulseelectronics.com automotive chip choke emi suppression for can-bus networks 2-line common mode chokes ?
3 pe-1812acc101sts impedance vs frequency temp vs dc current 0. 0 10. 0 20. 0 30. 0 40. 0 50. 0 60. 0 70. 0 0. 00 .1 0. 20 .3 0. 40 .5 0. 60 .7 id c( a) e t( ) et@ 25 0. 0 10. 0 20. 0 30. 0 40. 0 50. 0 60. 0 0. 00 0. 10 0. 20 0. 30 0. 40 0. 50 id c( a) e t( ) et@ 25 1.0 10 .0 10 0.0 10 ,0 00.0 10 0,000. 0 11 01 00 1,00 0 impedance() frequency(mhz) co mmo n mo de di?eren al mode 1.0 10 .0 10 0.0 1,00 0.0 10 ,0 00.0 10 0,000. 0 11 01 00 1,00 0 impedance() co mmon mode di?eren al mode pe-1812acc510sts 0. 0 10. 0 20. 0 30. 0 40. 0 50. 0 60. 0 70. 0 0. 00 .1 0. 20 .3 0. 40 .5 0. 60 .7 id c( a) e t( ) et@ 25 0. 0 10. 0 20. 0 30. 0 40. 0 50. 0 60. 0 0. 00 0. 10 0. 20 0. 30 0. 40 0. 50 id c( a) e t( ) et@ 25 1.0 10 .0 10 0.0 10 ,0 00.0 10 0,000. 0 11 01 00 1,00 0 impedance() frequency(mhz) co mmo n mo de di?eren al mode 1.0 10 .0 10 0.0 1,00 0.0 10 ,0 00.0 10 0,000. 0 11 01 00 1,00 0 impedance() co mmon mode di?eren al mode w717.b (11/15) pulseelectronics.com automotive chip choke emi suppression for can-bus networks 2-line common mode chokes ?
4 item reference documents test condition test specifcation 1. high temperature exposure mil-std-202 method 108 1. temperature: 125 ? c 2. time: 96 hours 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 2. temperature cycling jesd22 method ja-104 1. temperature: 40 ? c ~ 125 ? c 2. number of cycles: 96 cycle 3.dwell time: 30 minutes 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 3. biased humidity test mil-std-202 method 103 1. temperature: 85 5 ? c 2. time: 96 hours 3. humidity: 85 5% rh 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 4. operational life mil-prf-27 1. temperature: 125 ? c 2. time: 96 hours 3. apply rated current 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 5. external visual mil-std-883 method 2009 inspect product construction, marking and workmanship per product specifcation standard 6. physical dimensions jesd22 method jb-100 verify physical dimensions to the applicable product detail specifcation per product specifcation standard 7. resistance to solvents mil-std-202 method 215 immerse into solvent for 3 0.5 minutes & brush 10 times for their cycles. 1. no body change in appearance 2. no marking blurred. 3. inductance shall not change more than 30% 8. vibration test mil-std-202 method 204 1. frequency and amplifed: 10-2000-10 hz, 1.5mm 2. direction: x, y, z 3. test duration: 2 hours for each direction, 6 hours in total 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 9. resistance to soldering heat test mil-std-202 method 210 1. temperature: 250 5 ? c 2. time: (temp. 217 ? c) 60 ~ 150 second 3. ir refow times: 3 times 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 10. rated current mil-std-202 method 330 apply rated current for 5 seconds. 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 11. temperature rise mil-prf-27 apply rated current for 10 minutes. 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 12. over load mil-prf-27 apply twice as rated current for 5 minutes. 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 13. solderability test j-std-002 1. bakeing in pre-testing: 155 5 ? c / 16hours 30min. 2. peak temperature: 240 5 ? c 3. time: (temp. 217 ? c) 60 ~ 150 second 4. ir refow times: 1 time the terminal shall be at least 95% covered with fresh solder. 14. electrical characterization user spec. 1. operating temperature:-40 ? c ~ 125 ? c 2. room temperature: 25 ? c 1. no mechanical and electrical damage 2. inductance shall not change more than 30% 15. withstanding voltage test mil-std-202 method 201 1. dv: 500v 2. time: 1 minute 1. during the test no breakdown. 2. the characteristic is normal after test. 16. drop jesd22-b111 package & drop down from 1m. in 1 angle 1 ridge & 2 surfaces orientation 1. no case deformation or change in appearance. 2. inductance shall not change more than 30% 17. terminal strength test jis-c-6429 1. apply push force to samples mounted on pcb. 2. force of 1.8 kg for 60 1 seconds. after test, inductors shall be on mechanical damge. reliability test w717.b (11/15) pulseelectronics.com automotive chip choke emi suppression for can-bus networks 2-line common mode chokes ?
5 for more information pulse worldwide headquarters 12220 world trade drive san diego, ca 92128 u.s.a. tel: 858 674 8100 fax: 858 674 8262 pulse europe einsteinstrasse 1 d-71083 herren - berg germany tel: 49 7032 78060 fax: 49 7032 7806 135 pulse china headquarters b402, shenzhen academy of aerospace technol - ogy bldg. 10th kejinan road high-tech zone nanshan district shenzen, pr china 518057 tel: 86 755 33966678 fax: 86 755 33966700 pulse north china room 2704/2705 super ocean finance ctr. 2067 yan an road west shanghai 200336 china tel: 86 21 62787060 fax: 86 2162786973 pulse south asia 135 joo seng road #03-02 pm industrial bldg. singapore 368363 tel: 65 6287 8998 fax: 65 6287 8998 pulse north asia 3f, no. 198 zhongyuan road zhongli city taoyuan county 320 taiwan r. o. c. tel: 886 3 4356768 fax: 886 3 4356823 (pulse) fax: 886 3 4356820 (fre) performance warranty of products ofered on this data sheet is limited to the parameters specifed. data is subject to change without notice. other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. ? copyright, 2015. pulse electronics, inc. all rights reserved. tape and reel specifcations series parts per reel a b c d e w p1 p2 p3 h t 1812 acc 500 178 60 13 17 14 12 2 8 4 4 0.35 reel dimensions (mm) tape dimensions (mm) iii. description : a. ferrite drum core construction b. magnetically shielded c. enameled copper wire: h class d. product weight: 0.15g (ref.) e. moisture sensitivity level 1 f. products comply with rohs requirements g. halogen free available iv. general specifcation: a. storage temp: -40 ? cto+125 ? c b. operating temp: -40 ? cto+125 ? c (temp. rise included) c. resistance to solder heat: 250 ? c 10 secs. recommended solder heat resistance profle pulseelectronics.com automotive chip choke emi suppression for can-bus networks 2-line common mode chokes w717.b (11/15) ?
|
